Other /

How much chlorine should I put in my well water?

How much chlorine should I put in my well water?

CALCULATE AND POUR: Pour 3 pints of chlorine bleach per 100 gallons of water plus an additional 3 pints into your well as described above. MIX: Attach a clean garden hose to the outdoor faucet nearest the well and place the end of the hose inside the well.

How much bleach do you put in a chlorinator?

Use unscented chlorine laundry bleach (which is typically about 5% chlorine) and dilute it by adding 9 gallons of water to 1 gallon of bleach. This will give you a solution strength of approximately 5000 parts per million of chlorine.

What chlorine concentration should be produced when disinfecting a well or well pump?

50 to 100 parts per million
Disinfectant should be placed in the well in quantities that should produce a minimum concentration of at least 50 to 100 parts per million (ppm or mg/l). Use extreme caution when following this procedure. Chlorine is a strong oxidizing agent and is highly corrosive, especially at levels over 100 to 200 ppm.

How much bleach does it take to purify 1000 gallons of water?

A general rule of thumb to shock chlorinate and disinfect a storage tank is to mix non-scented NSF-approved household bleach (5.25% chlorine) in the reservoir at the ratio of 1 gallon of bleach for every 1,000 gallons of water (i.e., 1 quart for every 250 gallons of water).

Can you put too much chlorine in a well?

Do not use excessive amounts of bleach – more is not more effective. 5) For best results the bleach should be combined with water before adding it to the well. [By reducing the concentration there is less chance of corrosion of the cables and pipes in the well.

How do you inject chlorine into well water?

Chlorine is injected with a pump (commonly known as a chemical injection pump, a chemical feed pump or a chemical dosing pump) into the water between the well and the bladder (or pressure) tank. It then runs through a large retention tank to allow contact time.

How do you bleach a well water system?

Mix 2 quarts bleach in 10 gallons of water; pour into well. Connect a garden hose to a nearby faucet and wash down the inside of the well. Open each faucet and let the water run until a strong chlorine odor is detected, then turn it off and go to the next one. Don’t forget outdoor faucets and hydrants.

How much bleach do I add to 55 gallon water for storage?

How to Disinfect Water in a 55-Gallon Barrel for Long-Term Storage

  1. Add 1/4 teaspoon of calcium hypochlorite to the filled barrel and screw the lid on.
  2. Add 2 Tablespoons of FRESH unscented regular bleach (sodium hypochlorite).
  3. Add 1 bottle of Water Preserver Concentrate.

How much bleach is needed to shock a well?

4) Work out how much bleach will be needed: For every 50 gallons of water in the well use one quart of laundry bleach – (4 quarts in a gallon). Do not use excessive amounts of bleach – more is not more effective.

Why does my well water turn brown when I add bleach?

The brown is the iron in the water that has oxidized as a result of the chlorination. Normally, the iron in water is in ion form and does not display itself until it combines with oxygen and forms common rust which turns the water reddish-brown.

How long does it take to get chlorine out of well water?

Monitor the process, it can take 30 minutes to 24 hours or more to flush all of the bleach solution from the well. Use chlorine test papers to verify that the water coming from the outside faucet or yard hydrant is clear of any bleach solution. Flush the chlorinated water from water heaters.

When should you chlorinate your water well?

If your annual water test results show that bacteria is present. If you notice a change in the color, smell or taste of your drinking water, you should test for bacteria and will need to chlorinate the water if the test If the well is new, or has recently undergone repairs, or new pipes have been added.

How do you chlorinate a water well?

Chlorinating the Well Turn off the circuit breaker feeding the pump. Open the vent or remove the test hole plug. Pour in the bleach. Attach the hose. Recirculate the water. Test for chlorine. Wash down the sides of the well. Test for chlorine indoors. Wait 12 to 24 hours.

How to chlorinate well system?

Put your water treatment back on line and in service position. Make sure the time of day is correct since you are…

  • Wipe the inside of your sediment filter with a bleach solution before putting in a new filter. You should be doing…
  • As an extra precaution, you could add 1 ounce of chlorine to your salt tank and…

    • How to shock chlorinate a well?

    Determine the depth of water in the well. From the well log,look up the well depth and the depth to water table.

  • Measure the diameter of the well casing.
  • Measure the amount of chlorine bleach or HTH from the tables below,pour into a bucket,and dissolve in about 3 gallons of water.
  • Fill a 5-gallon bucket with clean water and set aside if needed for cleanup.
  • Connect a clean hose to a faucet in the system.
  • Take the top off of the well.
  • Pour in the chlorine solution.
  • Turn on the hose and direct the water back into the well,washing down the sides of the well casing.
  • Go into the house and turn on every tap until you smell chlorine then turn them off.
  • Let the water stand in the pipes for at least 12 and up to 24 hours.
  • Flush the system until the strong chlorine smell dissipates. Start with the outside hose and let it run on the ground away from the septic system.
  • Wait about two weeks and retest the well for bacteria. If shock chlorination did not eliminate the problem,a continuous disinfection system might be needed.