How do I fix error code 1E?

How do I fix error code 1E?

Disconnect the strainer, clean and rinse it, as it may become clogged. Check the condition of the hose. It is possible that it is pinched, clogged, bent or twisted. Unplug the washing machine: unplug the cord and plug it into the power outlet after 5-10 minutes to reset error code 1E.

What does error code ie mean on LG dishwasher?

Water does not fill the appliance properly. Turn off the appliance. Check the following for the IE error: Check the water pressure.

How do I clear the error on my LG dishwasher?

A small float element is activated when there is water in the sump and sends a signal to the control board. But it happens that the AE error code is associated with a short-term failure. To reset it, unplug the dishwasher for at least 10-15 minutes and turn it back on.

What does E1 mean on my LG dishwasher?

An E1 error code, programmed in the LG dishwasher, means that your appliance is leaking. If there is a leak, water accumulates in this pan and raises the float to the top, which closes the contacts.

How do you fix IE error on LG top load washer?

An IE error code indicates that the washer was unable to fill with water….

  1. Turn off the home’s hot and cold water supply taps/valve.
  2. Remove the water inlet hoses from the washer.
  3. Check the inlet filters on the inlet valves of the washer, inspect for any mineral deposits or other debris that may be clogging them.

How do I clear the IE code on my LG washing machine?

Turn off the home’s hot and cold water supply taps/valve. Remove the water inlet hoses from the washer. Ensure to have a bucket to drain the remaining water from the hoses. Check the inlet filters on the inlet valves of the washer, inspect for any mineral deposits or other debris that may be clogging them.

How do I reset E1 error on LG dishwasher?

Remove and replace the sump or float assembly if you find that is the cause of the E1 error code. How To Reset An LG Dishwasher? – Turn the circuit breaker or unplug the dishwasher for 10 to 15 seconds. – Plug the dishwasher back in or turn the circuit breaker back on.

How do I reset my LG Direct Drive dishwasher?

This can usually be corrected by performing the following steps:

  1. Press the POWER button to turn the dishwasher off.
  2. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds.
  3. Turn the circuit breaker to the dishwasher back ON.
  4. Press the POWER button to turn the dishwasher ON, and start a new cycle.

How do I fix E1 error on my dishwasher?

There is a float switch in the base that will detect this overflow and display the AE / E1 error code. To check if water is in the base, TURN OFF THE BREAKER and then you can easily remove the kickplate and check in the bottom middle of the dishwasher to see if the base is accessible.

How do I clear the IE code on my LG washer?

What is IE in LG washing machine top load?

An IE error code indicates that the washer was unable to fill with water. During cold and freezing weather conditions, an IE error code could mean the water in the water supply lines are frozen. Once the temperature increases above freezing, the water supply will resume.

What does error code IE mean on LG dishwasher?

Watch this video to learn about Understanding Error Codes – LG Dishwasher. An IE error code indicates that the level of water in the unit did not get high enough after 10 minutes of filling. To resolve this error, please check the following: Newly Installed units.

How do I fix the he error code on my Whirlpool dishwasher?

Press the POWER button to turn the dishwasher off. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds. Turn the circuit breaker to the dishwasher back ON. Press the POWER button to turn the dishwasher ON and start a new cycle. If the HE error code persists, the unit will require a repair service.

How do I troubleshoot a Samsung dishwasher that won’t start?

Press the POWER button to turn the dishwasher off. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds. Turn the circuit breaker to the dishwasher back ON. Press the POWER button to turn the dishwasher ON, and start a new cycle. If the CE or LE error code persist, the unit will require a repair service.

How do you fix a dishwasher that won’t drain?

The dishwasher has detected that there is too much water in the unit, and the drain pump is automatically turned on. This can usually be corrected by performing the following steps: Press the POWER button to turn the dishwasher off. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds.